Recent Posts

Donate Via Paypal and Help Support this site.

   

The HFAY layouts seem to all have the start lines where I would think is furthest away from the drivers? Is this correct? I am fitting this in an area that does not allow standing on both sides very well, so I am wondering the best way to set this up.

See pic. (1) or (2) the intention of the layouts? It makes sense to me that the bottom of the pic is where you would normally stand, but maybe people just do it more random? I just don't want to set it up then find out it would have been better with the starting line in the front next to where you stand.



Thanks.

Smooth or Rough side up? I cannot find the answer to this and it does not seem to be in the rules unless I am overlooking it. 

Just a note.   Feb 4th will be HFAY,   we'll use the 11th for a Test and Tune for Wyoming and get everyones cars ready.  (this will be a club race night, so of course everyone is welcome to come race.)

I think that will work. Gonna be alot of Racing in February!! 

I have racing scheduled on Feb 4th,  11th, so we can get our usual HFAY races in before we leave for the wyoming trip.   we could reverse the races and just run HFAY on the 4th,  then to a test and tune on the 11th to get ready for Wyoming?

Let me Know what you think.

Here is the Schedule for 2015.

The following times will be for all races unless otherwise noted or posted change.

5:30 pm   -  Track Setup
6:00 pm   -  Open Practice
7:00 pm   -  Racing until done !!!  

January 7th  (Classes: Racer, F1, Overland, Buggies)
January 21st (Classes: Racer, F1, Overland, Buggies) (HFAY)
Feb 4th (Classes: Racer, F1, Overland, Buggies) (HFAY)
Feb 11th (Classes: Racer, F1, Overland, Buggies)
February 19th, 20th and 21st **Wyoming Race**  Road Trip
(Cancelled)March 3rd (Classes: Racer, F1, Overland, Buggies)(Cancelled)
March 17th (Classes: Racer, F1, Overland, Buggies)
March 31st (Classes: Racer, F1, Overland, Buggies)(HFAY)
April 14th (Classes: Racer, F1, Overland, Buggies)
April 28th (Classes: Racer, F1, Overland, Buggies) (HFAY)
May 19th (Classes: Racer, F1, Overland, Buggies, Monster Truck)
May 26th (Classes: Racer, F1, Overland, Buggies, Monster Truck)(HFAY)
June 9th (Classes: Racer, F1, Overland, Buggies, Monster Truck)
June 23rd (Classes: Racer, F1, Pan)(HFAY Large Track)
(this will be setup outside in the driveway, come early if you can to help setup, thanks)
July 7th (Classes: Racer, F1, Overland, Monster Truck)
July 21st (Classes: Racer, F1, Overland, Monster Truck) (HFAY)
August 4th (Classes: Racer, F1, Pan) (Summer Enduro)
(this will be setup outside in the driveway, come early if you can to help setup, thanks)
August 18th (Classes: Racer, F1, Buggies, Monster Truck) (HFAY)
September 8th (Classes: Racer, F1, Overland, Buggies Monster Truck)
September 15th (Classes: Racer, F1, Overland, Buggies Monster Truck)
September 29th (Classes: Racer, F1, Overland Buggies, Monster Truck) (HFAY)
October 13th (Classes: Racer, F1, Overland, Buggies, Monster Truck)
October 27th (Classes: Racer, F1, Overland, Buggies, Monster Truck) (HFAY)
November 10th (Classes: Racer, F1, Overland, Buggies, Monster Truck)
November 17th (Classes: Racer, F1, Overland, Buggies, Monster Truck)(HFAY)
December 1st (Classes: Racer, F1, Overland, Buggies, Monster Truck)
December 15th (Classes: Overland, Racer, F1, Pan Car, Buggies if we have time)(HFAY BTE)
December 29th (Classes: Racer, F1, Overland, Buggies, Monster Truck)

yes we are racing on the 17th,   I have a couple of loaner cars you are welcome to come out and use for the night as well. 

I'll pm you the address.   you can show up any time after about 5pm.  I'll get you setup to race for the night. 

Show up ready to have some fun!!

Me and my buddy are looking to get into Mini-z's (we currently race 1/10 SCTs). We would like to see a race first. Are you racing on the 17th? If so, can you PM me the directions and time? Thanks in advance.

I know the original 03S boards had fets on only one side of the board but had pads on the bottom without fets.   there is now a version 2 03S board out but I haven't seen one so not sure on all the differences.

y'all;
in order to have my MR03S use different brushed motors,
i have embarked on changing the fets on my MR03S controller board.

it has been a long and costly endeavour but
i have finally soldered a new set of fets (4) onto my
original MR03S controller board.

during this learning process i have come across different
versions of the MR03S controller board.

i had purchased a MR03S controller board to practice on.  this separate controller board only had
pads for 2 fets and they were located on the bottom side of the board.  unfortunately, i lifted
some of the copper trace on this board, and rendered it unuseable.  i saved the pot
and servo motor for spares.

so i began to replace the fets on my original MR03S readyset car.  the controller card
in this MR03S car had soldering pads for 4 fets, 2 on the top side, and 2 on the bottom side.
this time around, i successfully replaced the 2 existing fets, and added 2 more on the
other side of the board.  i have tested this controller board and it is working,  and there is
no time delay (approx .5 sec) when switching from forward to reverse !

so, after all this, i want to put out the following questions:
- are there different versions of the MR03S controller board ?
- if so,  which version contains the soldering pads for 2 fets on top and bottom face
of the controller card ?

the controller board with the soldering pads for 4 fets (2 on top, 2 on bottom) is the preferred board to have for this modification, IMO...

unfortunately, i cannot post pics cause an error message is informing me there is no more room for
attached pics.

thank you for your help,
billp

briankstan
Russ
Ryan
Chad
CLODGUY
wild child
benihanna80
trackstar

Utah RC Forums

Mini-Z Forums

  RCP Race Tracks

Mini-Z Racing Venues

Salt Lake Mini-Z Online Store